Author Topic: Flying J CB550 Cafe Racer Magazine. (Read 182716 times)

SF · « **Reply #500 on:** August 05, 2011, 12:25:26 PM »

THAT IS PROBIBLY THE BEST POLISH JOB IVE SEEN, VERY NICE

hapakev · « **Reply #501 on:** August 05, 2011, 12:34:55 PM »

Did you have Cycle X coat the rocker arms?

Flying J · « **Reply #502 on:** August 05, 2011, 12:37:47 PM »

Yes, came out to around 109

Tintop · « **Reply #503 on:** August 05, 2011, 06:40:53 PM »

Very nice polish job, show quality.

Danno · « **Reply #504 on:** August 07, 2011, 11:26:32 AM »

hey bud they all weep a little from there on the head try spraying it down a couple of time with carb clean it may stop
as for your idle problem take the slow jets out and run a piece of (strand) 14 gauge wire through them and clean them well
also it sounds like you have an air leak take the little aluminum caps off the top of the carbs and use cable lube in them this will last for about a year other places they typically leak air is around the side O rings between the carbs and the boots themselves if the side o rings are the problem could indicate a worn throttle shaft
you can figure out where it is by spraying wd40 over these areas while running the rpm's will change but im betting on the slides being dry and hanging up in the bore cable lube works best but wd40 will work for a while also if the gasket is torn replace it you can cut your own from cardstock and an exacto knife works good not a lot of heat here so asbestos is overkill

Tintop · « **Reply #505 on:** August 07, 2011, 12:08:59 PM »

huh...

Flying J · « **Reply #506 on:** August 07, 2011, 02:43:49 PM »

WTF Danno?
Read the whole thread first or at least look at the date of the post your replying to, that was years ago.

FunJimmy · « **Reply #507 on:** September 01, 2011, 10:27:59 PM »

ffJ

I see Chris from MotoGP has listed your exhaust on ebay, stating that you have run into $$$ troubles so he is selling then at half price.

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&_trksid=p5197.c0.m619&item=120771727808&viewitem=&category=35596

Hope all is going well and that he is misinformed about your personal situation.

FJ

Flying J · « **Reply #508 on:** September 01, 2011, 10:39:46 PM »

No.I got my pipes already. I paid 8 for mine so it will be ingesting to see how much they go for. Pretty funny he says he built them for a guy back east. I live 4 hours from chris and when I bought mine he said he only made 2. I could never get a read on the guy. Sometimes he seems really shady, as you have experienced I'm sure and other times he has been really cool and helpful. I was happy to get my pipes and he saved me some money on my rims. I wonder if he will ship those pipes to canada? Last I talked to him he had an embargo against canada. Lol

Retro Rocket · « **Reply #509 on:** September 01, 2011, 10:51:08 PM »

I saw the same style pipe for a 750 advertised on ebay a while back also, so i think he has been making more. Wouldn't mind a set for my F build.....Nice

Check out the pics in this link.... I know this is an auction for a yoshi but look at all the pics....

http://cgi.ebay.com/ebaymotors/CB750-EXHAUST-YOSHI-REPS-CB-750-STAINLESS-4N1-/120764750778?pt=Motorcycles_Parts_Accessories&hash=item1c1e23dbba

scunny · « **Reply #510 on:** September 02, 2011, 01:01:48 AM »

those 4/4's look good. if CHCH manages to survive this year I would love a set of those,

FunJimmy · « **Reply #511 on:** September 02, 2011, 07:10:21 AM »

Quote from: ffJMoore on September 01, 2011, 10:39:46 PM

I wonder if he will ship those pipes to canada? Last I talked to him he had an embargo against canada. Lol

Ya, I don’t know where he stands on the Canadian embargo anymore. I gave in to the constant harassment and returned the Yosh replica pipe to him over 3 months ago so he shouldn’t have to hold an entire country responsible anymore.

Bike is looking fantastic ffj.

70CB750 · « **Reply #512 on:** September 08, 2011, 07:42:56 AM »

Quote from: ffJMoore on July 23, 2011, 11:21:12 AM

Got the rear wheel trued to .02" Not Bad. Just need to get the wheel on it. What a mess it was to get the correct size rim to my house. Still have the 2.15x 18 if anybody wants it. $215 rim and ill sell it for less.

23999

Still got the wheel?

B.O.X.N.I.F.E. · « **Reply #513 on:** September 21, 2011, 02:19:56 PM »

Quote from: ffJMoore on September 01, 2011, 10:39:46 PM

No.I got my pipes already. I paid 8 for mine so it will be ingesting to see how much they go for. Pretty funny he says he built them for a guy back east. I live 4 hours from chris and when I bought mine he said he only made 2. I could never get a read on the guy. Sometimes he seems really shady, as you have experienced I'm sure and other times he has been really cool and helpful. I was happy to get my pipes and he saved me some money on my rims. I wonder if he will ship those pipes to canada? Last I talked to him he had an embargo against canada. Lol

He was weird to deal with. The 4-1 he built me is kind of a rough fit, it needs tweaking. But Lord it's a nice looking pipe.

Flying J · « **Reply #514 on:** October 14, 2011, 12:13:20 PM »

Ok folks after much delay and distraction by other bikes im back on this build. Split the cases on my big bore build( see my motorbuild for details on that) and then i pulled the motor out of my rolling frame and took the bike to my upholstery guy. Should have a nice seat in the next week or so. Stay tuned.

Flying J · « **Reply #515 on:** October 14, 2011, 01:34:40 PM »

Oh and if you dont follow all my builds here is distraction i speak of

lucky · « **Reply #516 on:** October 14, 2011, 02:04:53 PM »

Quote from: ffJMoore on May 27, 2009, 10:10:03 PM

got a stock seat put on and im working out some problems with the carbs. My list of to do's for tomorow is.
get the carbs to stop leaking
get the chain on
get the breaks on
prep the spare wheels for Powder coat
work on switches and headlight.
well see how much gets done
ill post pics with the new seat.

It is easy to get the carbs to stop leaking .

Just install 4 new float needle jets.

Do not adjust the floats to get it to stop leaking - or you will end up just having to do the job all over again.

The only way the floats get off is when the rubber tipped float needles get old and crushed down, shrunken and out of round. Also they get hard and will not seal properly.

Just put in new float needles and make sure you can see daylight when you look through the idle jets.

Flying J · « **Reply #517 on:** October 14, 2011, 02:22:54 PM »

Lucky are you retarded? Anybody know wtf is wrong with this guy?

brandEn · « **Reply #518 on:** October 14, 2011, 02:24:44 PM »

Quote from: ffJMoore on October 14, 2011, 02:22:54 PM

Lucky are you retarded? Anybody know wtf is wrong with this guy?

haha I just lol'ed

maduncle · « **Reply #519 on:** October 14, 2011, 11:10:21 PM »

Quote from: brandEn on October 14, 2011, 02:24:44 PM

Quote from: ffJMoore on October 14, 2011, 02:22:54 PM
Lucky are you retarded? Anybody know wtf is wrong with this guy?

haha I just lol'ed

I think 'TDC challenged' is the politically correct term (I read that on this forum somewhere).

Maybe Lucky is just being thorough...

BTW - I like your distraction project.

Flying J · « **Reply #520 on:** October 21, 2011, 01:04:33 PM »

Teaser

27887

SF · « **Reply #521 on:** October 21, 2011, 01:09:56 PM »

NICE! LINES FLOW JUST LIKE YOUR TANK, WILL YOU HAVE ENOUGH ROOM FOR EVERYTHING UNDER THERE?

Flying J · « **Reply #522 on:** October 21, 2011, 01:14:36 PM »

Greggo · « **Reply #523 on:** October 21, 2011, 02:56:27 PM »

Nice! Don't see too many with that shape, kinda looks like that Manx style. Me likee!

hapakev · « **Reply #524 on:** October 22, 2011, 11:51:24 AM »

Did you sew that up? Looks great man.

News:

Author Topic: Flying J CB550 Cafe Racer Magazine. (Read 182716 times)

maduncle