Topic: What did you do to your bike today ?

[grcamna2]

'bear claw' foot pegs done

How it's looking at the moment

Side covers pretty much done

I like all the mods done here. Especially the exhaust header clamps.

Do they do the job? No leaks? Where did you source them?

Spotty,I noticed the cover off;how's your shifting mechanism ?

[88BuckMeister]

I sanded my fuel tank to try and figure out why in the hell the last guy covered the emblem mounts in bondo. I've successfully dug them out. I still have no answers as to why the hell the last guy buried them in bondo. New Honda tank emblems costed me like 60 bucks

[grcamna2]

I sanded my fuel tank to try and figure out why in the hell the last guy covered the emblem mounts in bondo. I've successfully dug them out. I still have no answers as to why the hell the last guy buried them in bondo. New Honda tank emblems costed me like 60 bucks

Sometimes certain owners do the 'emblem delete' on the tank when they repaint the bike.
I imagine it looks better to them without the emblems;a certain 'smooth/clean' look.

[spotty]

'bear claw' foot pegs done

How it's looking at the moment

Side covers pretty much done

I like all the mods done here. Especially the exhaust header clamps.

Do they do the job? No leaks? Where did you source them?

Spotty,I noticed the cover off;how's your shifting mechanism ?

i've never ridden the bike but the PO reckons theres nothing wrong in that department, i can't remember why i took the cover off

[BenelliSEI]

Four shiny covers!

[grcamna2]

I really like the stator cover too 

[Gurp]

Four shiny covers!

Bud! You did a heck of a job. They look great!

Sent from my LE2127 using Tapatalk

[BenelliSEI]

Better on the bike!

[Gurp]

Better on the bike!

Shewwww-eeeee
Talk about clean.
You could eat off that thing!

Sent from my LE2127 using Tapatalk

[M 750K6]

Super job. 👍

Envy your undamaged points cover!

[BenelliSEI]

Super job. 👍

Envy your undamaged points cover!

It had a tiny ding I pushed out. I only have one really good one left, for the S/C!

[MauiK3]

Nice polishing, looks chromed.

[Stev-o]

Was a great day in Central Texas yesterday, decided to roll the CB750 out of the garage.  Cranked it over, seemed starter was a little slow, but after 3 cranks, she fired up! [it's been about 2 months since riding this bike]  Sunny and 70 degrees, perfect day to go for a ride, I love winter-time in Texas....

[Gurp]

When out to start to CB project.
smelled gas as I opened the shop door.
i had one float a bit high and one leaking bowl gasket. carbs 1 and 2. cleaned up the gas and it fired up and idled well enough for now.
waiting on parts to do much more with it ATM.

[Stev-o]

When out to start to CB project.
smelled gas as I opened the shop door.

Did you leave the petcock on?   

[Gurp]

When out to start to CB project.
smelled gas as I opened the shop door.

Did you leave the petcock on?   

Yes.

Sent from my LE2127 using Tapatalk

[Magpie]

A good friend gave me an engine stand so I did a major clean up of the engine for my K6. I should have bought a stand long ago!

[Floshenbarnical]

A good friend gave me an engine stand so I did a major clean up of the engine for my K6. I should have bought a stand long ago!

Why is this the single most British image I have ever seen? I can practically smell a steak and kidney pie

[spotty]

A good friend gave me an engine stand so I did a major clean up of the engine for my K6. I should have bought a stand long ago!

i've got terrys engine stand at my place and i was thinking this would be a good idea for when the time comes to clean/paint my engine
could you chuck a picture up of how its all bolted up at the back ? did you make brackets to turn the attachment points 90 degrees to attach to the motor

[lash]

Here’s mine..just some pieces of angle iron and bolts

[spotty]

Here’s mine..just some pieces of angle iron and bolts

thanks for that

[BenelliSEI]

Spotty….. I used two pieces of angle (4” X 4””). One set of holes for the rear through bolts on the engine and four bolts directly to the main plate on the stand.

What you can’t see clearly is a bit of “shaping” (with a grinder) around the clutch cover where the kick start shaft is located.

[newday777]

This is what I cut up to make the motorstand adapters. I used some 2"×3" angle iron and cut Vs out to clear the back sides of the cases.

I picked up this K5 motor a couple years ago as it was pulled out of a chopper, low miles on an 836 build, ported head, SS2 cam + springs and titanium keepers. I still have to go through it and inspect the insides as well as vaporblast the paint off and repaint.

[newday777]

A friend in California has this stand off bracket welded up

[WhyNot2]

Still haven't installed this tank yet, but the CB750 will be going on the table this week.

Agenda:

Change rear swingarm with a CB550 one.
Change front forks with CB550 set.
Try my hand again at polishing some pieces.
Will try to do some rewiring to clean up the rats nest in the headlight.

If I can get to it.......the shop called and finally after 2 years, the head for the frankenbike CB/CL/SL350 twin is ready.
Been messing with this thing a few years or more.