Author Topic: Clean oil lines? (Read 3480 times)

dgilling · « **on:** February 14, 2015, 11:20:38 PM »

What's the best way to clean up the oil lines? Is it even worth it. Mine where all black, then I power washed them now they're a faded white with some black. Can you paint the nylon?

70CB750 · « **Reply #1 on:** February 15, 2015, 01:40:42 AM »

Your best bet is to figure out a replacement, every so often somebody reports a leak from the hose. The oil is under zero pressure in there but old hose will eventually leak.

martin99 · « **Reply #2 on:** February 15, 2015, 01:41:17 AM »

I used some of that plastic spiral armour sleeve stuff to tidy mine up, the kind used for bundling wiring together. No need to take off the hoses

bwaller · « **Reply #3 on:** February 15, 2015, 04:57:13 AM »

Black shoe polish!

flybox1 · « **Reply #4 on:** February 16, 2015, 07:37:50 AM »

I pressure washed them too. they came out light gray.
First i tried full strength RID fabric dye to darken them. It worked, but not well enough.
Once dried, I taped off the ends and used VHT flat black header paint.
Still look great after a year

dgilling · « **Reply #5 on:** February 16, 2015, 08:06:22 AM »

Thanks Flybox, I have some VHT header paint Left over. I'll paint them tonight.

PeWe · « **Reply #6 on:** February 16, 2015, 10:12:00 AM »

No risk that the rubber in the oil lines start to crack due to age?

Airborne 82nd · « **Reply #7 on:** February 16, 2015, 10:34:28 AM »

Quote from: PeWe on February 16, 2015, 10:12:00 AM

No risk that the rubber in the oil lines start to crack due to age?

I too would be more concerned about the inside. I vote clean up the ends and replace the old rubber. I went with the stainless mesh cover.

70CB750 · « **Reply #8 on:** February 16, 2015, 03:24:51 PM »

My point above, 40 years old rubber is nothing I would call reliable.

edwardmorris · « **Reply #9 on:** February 16, 2015, 03:32:12 PM »

Quote from: 70CB750 on February 16, 2015, 03:24:51 PM

My point above, 40 years old rubber is nothing I would call reliable.

Prokop, didn't you DIY braided stainless replacements? If you could please post up details, I'd like to save the leaky pair on my K3.....

70CB750 · « **Reply #10 on:** February 16, 2015, 03:45:30 PM »

Yes, I did. McMasterCarr has SS ferrules, your local hydraulic shop will match your fitting to a hose and all it heeds is a crimp.

Some members, like Kickstart, had luck just taking a hose to hydraulic shop and getting them crimped, I was never able to do that. Napa would not take a chance, Coliflower did not have the right size crimp, it was frustrating.

For my project I found finally this jig at Home Depot, it is used to crimp the new style of house water lines and I paid $25 or so for it and it crimped the hose well enough.

Here it is on Amazon, but I found it locally.

http://www.amazon.com/Superior-Tool-07100-Pocket-Crimper/dp/B002RBAADC

edwardmorris · « **Reply #11 on:** February 16, 2015, 03:52:08 PM »

Thanks! I'm having terrible luck at the local hose shops too. Somehow they knew they aren't standard hoses and pulled it outta me that they were for a motorcycle. Once they heard that, there was no talking to them. One more q, what size ferrules to go with? I'm sure I can figure out hose diameters, unless you know them off the top of your head....

oldhatt45 · « **Reply #12 on:** February 16, 2015, 05:53:27 PM »

Ed,

Try this place. http://www.indrubber.com/index.html
It is Industrial Rubber in Elizabeth, NJ.
They have done SCUBA Hoses (5000 psi), Gas Mixing whips (also 5000 psi), and High Pressure lines for the Detroit Diesels I had on my boat.
Admittedly this spans the last 20+ years, but possibly if you call them and ask, you'd only be out the price of a phone call at worst.

Hope this helps

Charlie

70CB750 · « **Reply #13 on:** February 17, 2015, 03:53:35 AM »

Quote from: edwardmorris on February 16, 2015, 03:52:08 PM

Thanks! I'm having terrible luck at the local hose shops too. Somehow they knew they aren't standard hoses and pulled it outta me that they were for a motorcycle. Once they heard that, there was no talking to them. One more q, what size ferrules to go with? I'm sure I can figure out hose diameters, unless you know them off the top of your head....

Yes, they would not take the responsibility or they did not have the spirit that makes things happen, suckers

I am pretty sure, these were the ferrules: 9256T35

Just put that code in the search on McMasterCarr web and it will come up.

http://www.mcmaster.com

edwardmorris · « **Reply #14 on:** February 17, 2015, 10:51:30 AM »

Quote from: 70CB750 on February 17, 2015, 03:53:35 AM

Quote from: edwardmorris on February 16, 2015, 03:52:08 PM
Thanks! I'm having terrible luck at the local hose shops too. Somehow they knew they aren't standard hoses and pulled it outta me that they were for a motorcycle. Once they heard that, there was no talking to them. One more q, what size ferrules to go with? I'm sure I can figure out hose diameters, unless you know them off the top of your head....

Yes, they would not take the responsibility or they did not have the spirit that makes things happen, suckers

I am pretty sure, these were the ferrules: 9256T35

Just put that code in the search on McMasterCarr web and it will come up.

http://www.mcmaster.com

Thank you! I'll give it a shot and post in my K3 build thread. I found a thread that had the correct hose dimensions listed, but now I can't find it again

Will post here when I do.

dgilling · « **Reply #15 on:** February 18, 2015, 10:26:59 AM »

So why not just buy new stainless ones from CB750 cafe for $69?

http://www.cb750cafe.com/products-page/cafe-parts/stainless-braided-oil-lines/

edwardmorris · « **Reply #16 on:** February 18, 2015, 02:20:34 PM »

Found the thread http://forums.sohc4.net/index.php?topic=15821.0

The DIY price is half of CB750 cafe price. I'm going to try this.

-10AN 3' stainless hose from Jegs : $20
9256T35 ferrules from McMaster: $5.51

say roughly $30 shipped for everything. Any local auto shop that provides A/C services will have a hose crimper or you can invest in one like Prokop posted above.

70CB750 · « **Reply #17 on:** February 18, 2015, 04:03:45 PM »

Quote from: dgilling on February 18, 2015, 10:26:59 AM

So why not just buy new stainless ones from CB750 cafe for $69?

http://www.cb750cafe.com/products-page/cafe-parts/stainless-braided-oil-lines/

First time I see them this cheap. Somebody here posted SS oil hoses he was making for $150 - 2 years ago or so.

seanbarney41 · « **Reply #18 on:** February 18, 2015, 09:06:27 PM »

How do you remove the old end fitting from the old hoses so the new stainless can be crimped on?

70CB750 · « **Reply #19 on:** February 19, 2015, 03:26:53 AM »

I use hacksaw and cut off the side of the ferrule, parallel to the hose. Or you can do what he did:

72 yellow · « **Reply #20 on:** February 19, 2015, 06:17:27 AM »

Looking at Carpy's oil lines, the ends are not crimped. They are held on by stainless hose clamps with covers.

dgilling · « **Reply #21 on:** February 19, 2015, 09:33:12 AM »

I feel like I have so much more to do that an extra $30 is worth it to just buy from cb750 cafe

seanbarney41 · « **Reply #22 on:** February 19, 2015, 01:11:16 PM »

Quote from: 70CB750 on February 19, 2015, 03:26:53 AM

I use hacksaw and cut off the side of the ferrule, parallel to the hose. Or you can do what he did:

ok, so the ferule is not part of the hose end fitting? I make a lot of hydraulic hoses at work and the part that gets crimped/ferule is an integral part of the hose end. They can only be crimped once.

70CB750 · « **Reply #23 on:** February 19, 2015, 03:12:58 PM »

Thats correct, the ferrule slips on the hose for the crimp.

These are not hydraulic hoses, only oil supply. They carry 0 psi pressure.

edwardmorris · « **Reply #24 on:** February 19, 2015, 03:18:16 PM »

Stuff's on its way, hopefully some pix soon when I get it together next week. Thanks Prokop and Mikeb4.

News:

Author Topic: Clean oil lines? (Read 3480 times)