Author Topic: turning your bike around. maybe you've seen this done or done it yourself  (Read 20044 times)

0 Members and 1 Guest are viewing this topic.

Offline 547

  • Hot Shot
  • ***
  • Posts: 295
I saw this done on youtube and it has been a very useful trick for me. i am getting better at it.

left hand on left grip
right hand on right side of grab rail
tip bike onto side stand
put pressure on back of the seat to get front wheel off the ground
then rotate
gets easier each time you do it
its like riding a unicycle
check it out
j-

Offline TwoTired

  • Really Old Timer ...
  • *******
  • Posts: 21,084
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #1 on: November 26, 2008, 08:11:40 pm »
I've done this. You have to have the side stand near the CG of the bike.  Some of the earlier 550s and 500 had the stand father forward.  When you get the weight onto the stand to use as a pivot, the side stand folds up.  If you are not prepared, it can ruin your day.

You also have to not care about marks on the floor from the side stand being used as a drill.

Cheers,
Lloyd... (SOHC4 #11 Original Mail List)
72 500, 74 550, 75 550K, 75 550F, 76 550F, 77 550F X2, 78 550K, 77 750F X2, 78 750F, 79CX500, 85 700SC, GL1100

Those that learn from history are doomed to repeat it by those that don't learn from history.

Offline Johnie

  • Really Old Timer ...
  • *******
  • Posts: 8,054
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #2 on: November 26, 2008, 08:17:53 pm »
Pretty dangerous thing to do if you had a vintage bike you cared about.  So what is accomplished here.  I can turn mine around while on both wheels.   
1970 CB750K0 - Candy Ruby Red
1973 CB750K3 - Candy Bacchus Olive
2000 1500 SE Wing (wife's pearl white bike)
1970 Chevy Chevelle SS396 - Cortez Silver

Oshkosh, WI  USA

Offline Really?

  • I am not a
  • Really Old Timer ...
  • *******
  • Posts: 5,241
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #3 on: November 26, 2008, 08:39:12 pm »
Hey Heff, this could get some new folks in the "Dropped the Bike Club" and some donations to SOHC4!

Offline 547

  • Hot Shot
  • ***
  • Posts: 295
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #4 on: November 26, 2008, 08:45:15 pm »
ok! ok! maybe i haven't thought this through... ???
could be disastrous
j-

Offline UnCrash

  • Pass
  • Master
  • *****
  • Posts: 1,705
    • My Blog
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #5 on: November 27, 2008, 05:35:51 am »
Quote
Hey Heff, this could get some new folks in the "Dropped the Bike Club" and some donations to SOHC4!

my thoughts exactly...  The guy in the vid comes awful close to the tipping point!
You can't make too much popcorn, but you can definately eat too much popcorn.

rhos1355

  • Guest
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #6 on: November 27, 2008, 01:18:52 pm »
Seen a few mechanics in small cramped bike shops do this. But not novices.
Having said that I've always wondered how those bike shop guys seem to wheel the biggest, clumsiest bikes around with such apparent ease.
I once saw one guy, knee high to a grass-hopper he was, run a bike for a few yards then hop on side saddle style and coast all the way from the back of the lot to the shop.
I if I tried that I'd be arse over in no time!

Offline andy750

  • Really Old Timer ...
  • *******
  • Posts: 7,623
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #7 on: November 27, 2008, 01:42:19 pm »
I saw a really small guy riding a sports bike and everytime he came to traffic lights he would slide off one side and then hope back on when the lights changed...very funny to watch but due credit to him...some are just under-tall.

Anyway....as for pivoting bikes on sidestands...accident waiting to happen...no thanks...Ill stick to two wheel turnarounds.

cheers
Andy

Current bikes
1. CB750K4: Long distance bike, 17 countries and counting...2001 - Trans-USA-Mexico (CB750K4), 2003 - European Tour (CB750K4), 2004 - SOHC Easy Rider Trip (CB750K4), 2008 - Adirondack Tour 2-up (CB750K4) , 2013 - Tail of the Dragon Tour , 2017: 836 kit install and bottom end rebuild. And rebirth: http://forums.sohc4.net/index.php/topic,173213.msg2029836.html#msg2029836
2. CB750/810cc K2  - road racer with JMR worked head 71 hp
3. VStrom DL1000 2003
4. XLR650L 2006

Where did you go on your bike today? - http://forums.sohc4.net/index.php?topic=45183.2350

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,340
  • Today's Lesson: One good turn deserves another.
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #8 on: November 27, 2008, 03:49:50 pm »
Here's an interesting well made alternative from Telefix. Its the third thing down. I like it better that the turntables as you can move it all around while loaded.
http://www.motorworks.co.uk/bmw/products/product.php?f=g&code=BR&shnew=New&shnewcode=15&model=Accessories&part=Turntables+and+lifters&modelcode=90&partcode=BR

I've seen this on video too with a GoldWing on it and its really neat.  About $150.
« Last Edit: November 27, 2008, 03:52:48 pm by MCRider »
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."

Offline MCRider

  • Such is the life of a
  • Really Old Timer ...
  • *******
  • Posts: 14,340
  • Today's Lesson: One good turn deserves another.
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #9 on: November 27, 2008, 04:05:39 pm »
Here's a similar design. THis site has one for sidestand only models as well.
http://www.beckerenterprises.com/manual_mm.php
Ride Safe:
Ron
1988 NT650 HawkGT;  1978 CB400 Hawk;  1975 CB750F -Free Bird; 1968 CB77 Super Hawk -Ticker;  Phaedrus 1972 CB750K2- Build Thread
"Sometimes the light's all shining on me, other times I can barely see, lately it appears to me, what a long, strange trip its been."

Offline Hope

  • How did I become an
  • Expert
  • ****
  • Posts: 1,038
  • SOHC member since '01
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #10 on: November 27, 2008, 04:20:48 pm »
I've done this. You have to have the side stand near the CG of the bike.  Some of the earlier 550s and 500 had the stand father forward.  When you get the weight onto the stand to use as a pivot, the side stand folds up.  If you are not prepared, it can ruin your day.

You also have to not care about marks on the floor from the side stand being used as a drill.

Cheers,

I will not be trying this anytime soon with my 550.  I can see this going bad on very many different levels.  I really like my free inmate paint job.






I do the same type of "turn around" but I use the center stand instead. The bike will only need to be tilted slightly to accomplish the same thing.

I was using a similar method with my center stand until I noticed that I was wearing down my center stand.  I stopped as soon as I realized the wear on my center stand.
« Last Edit: November 27, 2008, 04:23:05 pm by Hope »

Offline ev0lve

  • Master
  • *****
  • Posts: 1,930
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #11 on: November 27, 2008, 08:26:26 pm »
I saw this done on youtube and it has been a very useful trick for me. i am getting better at it.

left hand on left grip
right hand on right side of grab rail
tip bike onto side stand
put pressure on back of the seat to get front wheel off the ground
then rotate
gets easier each time you do it
its like riding a unicycle
check it out

Oh hell no  :o Well,maybe... If I really, really had to. But otherwise no  ;D

Offline DME

  • Hot Shot
  • ***
  • Posts: 504
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #12 on: November 28, 2008, 01:46:32 am »
Used that "trick" for 10 years with all my bikes, still no mishaps.
Just got to be careful.

/Dan

Offline Hope

  • How did I become an
  • Expert
  • ****
  • Posts: 1,038
  • SOHC member since '01
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #13 on: November 28, 2008, 03:27:50 pm »
mmmmaybe if I had a really crappy bike I would try it ???

Offline DORIGTT

  • Full Member
  • *
  • Posts: 66
Re: turning your bike around. maybe you've seen this done or done it yourself
« Reply #14 on: November 28, 2008, 08:16:36 pm »
I read about this technique just over a decade ago and used it regularly for practical and show-off reasons.  People would trip out when you 'spun' your bike around in a tight spot like this.

Oh... hot asphalt, 430# Honda SuperHawk and the spin = band-aids on the cracked fairing.

Other than that, it worked great.  Be careful to not bend the stand with some of the really heavy bikes!

Offline axehole54

  • Who the heck decided to call me a
  • Hot Shot
  • ***
  • Posts: 315
  • #169 North
I grab the rear bar on my 750k, tilt it towards myself, and hip check/push till its where i want it... my buddy drives a 93 cbr and looks at me like I've lost it lol.
73 750k, 78 750k, 69 c10, 87 r1500 (c10), 94 fzr1000

Offline seaweb11

  • 1st Mate &
  • Really Old Timer ...
  • *******
  • Posts: 6,241
  • Ride & Smile
    • Playground Directory
I love it when the newbs bring up these oldies.   ;D ;D
Great can kick at the beginning, all business 8)  I still haven't tried it......

Offline razor02097

  • Not a fool, just an
  • Expert
  • ****
  • Posts: 767
  • Yes its a Honda You got an F'in problem with that?
wow... this thread has been dug from the grave!

I do this all the time with Rina (although I have replaced the kickstand twice  :o )
Project Rina

That is an inconceivably egregious transgression against my rudimentary concordance of socially shunned individuals.

Offline BobbyR

  • Really Old Timer ...
  • *******
  • Posts: 12,367
  • Proud Owner of the Babe Thread & Dirty Old Man
Quite clever, I will have to remember not to try that.  ;D
Dedicated to Sgt. Howard Bruckner 1950 - 1969. KIA LONG KHANH.

But we were boys, and boys will be boys, and so they will. To us, everything was dangerous, but what of that? Had we not been made to live forever?

Offline axehole54

  • Who the heck decided to call me a
  • Hot Shot
  • ***
  • Posts: 315
  • #169 North
Been trying that trick a few times as of late everyone thinks it looks pro ;D.  So as long as I don't dump the old girl  :P
73 750k, 78 750k, 69 c10, 87 r1500 (c10), 94 fzr1000

Offline Cvillechopper

  • Is just pretending to be an
  • Expert
  • ****
  • Posts: 1,184
  • If not for my failures I'd never know my limits
I don't get it.  Why don't you just grab the frame, lift her up and turn her around thus avoiding the use of the kickstand all together?  That would be much more impressive.   ;D
It is the mark of an educated mind to be able to entertain a thought without accepting it.  Aristotle

Offline Blueridgerunner

  • Enthusiast
  • **
  • Posts: 236
  • CB650 no longer, but do have an 87 GL1200
Both my bike and myself are too old for this  ;D
Said James "In my opinion,  there's nothing in this world, beats a '52 Vincent and a red headed girl"

Laissez les bons temps rouler

Offline BobbyR

  • Really Old Timer ...
  • *******
  • Posts: 12,367
  • Proud Owner of the Babe Thread & Dirty Old Man
Both my bike and myself are too old for this  ;D
I hear ya brother. Wound up under mine once, took a bit to wiggle out from under it.
Dedicated to Sgt. Howard Bruckner 1950 - 1969. KIA LONG KHANH.

But we were boys, and boys will be boys, and so they will. To us, everything was dangerous, but what of that? Had we not been made to live forever?

Offline Tretnine

  • Prove it,
  • Hot Shot
  • ***
  • Posts: 577
  • Figuring it out, one expletive at a time.
    • http://www.behindbarsmotorcycle.com/
I laughed at this, thinking this guy a total maniac. Then, in my driveway I realized I couldn't get my bike moved because the chain was binding (it's in project status) This trick looked like a dream.

The guy in the video kind of acts like a cock, though. The camera goes on about a minute before he does the trick so he can look cool on film. Meh. It helped me.
http://www.behindbarsmotorcycle.com/

2009 Kawasaki Concours, 1978 cb550k, 2006 BMW F650GS

Member of the AMA