« previous next »
Pages: [1]   Go Down

Author Topic: Swing arm bushings  (Read 3644 times)

0 Members and 1 Guest are viewing this topic.

Offline 77379

  • Full Member
  • *
  • Posts: 64
Swing arm bushings
« on: January 24, 2017, 03:05:09 PM »
I removed the bushings on my swing arm using the hacksaw method. It was much easier than I thought it would be. I used a new blade and made about ten strokes which went through about one eighth of  the bushing. I didn't want to accidentally cut at an angle and then cut into the frame. Then I removed the hacksaw blade and used a piece of black gas pipe that was in the garage, tapped it lightly and it came right out. I was surprised how easy it was. I'm looking for some advice on new replacement bushings. Both the front and rear shock ones for my CB750. I don't think the installation process will be as easy.
Gregg
Logged

Offline markreimer

  • Expert
  • ****
  • Posts: 1,192
Re: Swing arm bushings
« Reply #1 on: January 24, 2017, 03:31:45 PM »
It's probably easier! I used some bronze bushings and pressed them in with a pipe clamp I think. I polished the pivot shaft or whatever it's called and fitted a American style grease zerk in the end while I had it out. Simple conversion. After that it's install time. You don't need all the spacers that originally were used with the old style bushings. I believe the new ones are a top hat shape and you only need to add the cupped cap between the bushings and frame.

Put it all back together and pump grease till it's oozing out both ends. Check for side to side play - should be zero measurable play. None at all. Make sure the swing arm can slowly fall down under its own weight before you hook up the rear shocks. Then you know it's not binding.


Sent from my iPhone using Tapatalk
Logged

Offline timbo750

  • Expert
  • ****
  • Posts: 759
Re: Swing arm bushings
« Reply #2 on: January 24, 2017, 03:33:44 PM »
There is guy in europe who makes brass swing arm bushings. Best value and recommended by many, I got mine from him and a perfect fit and easy to fit, just need a soft blow hammer and a piece of wood.
Logged

Offline markreimer

  • Expert
  • ****
  • Posts: 1,192
Re: Swing arm bushings
« Reply #3 on: January 24, 2017, 03:36:50 PM »
Now I remember, I used a long piece of threaded rod with a big washer and nut on each end. As I tightened the nuts the bushings were pressed in. Dead blow works too but much easier to muck something up...


Sent from my iPhone using Tapatalk
Logged

Offline 77379

  • Full Member
  • *
  • Posts: 64
Re: Swing arm bushings
« Reply #4 on: January 24, 2017, 03:56:08 PM »
Timbo750, do you know how to contact the guy in Europe or the name of his company that sells the swing arm bushings? 
Logged

Offline danyo

  • Hot Shot
  • ***
  • Posts: 299
Re: Swing arm bushings
« Reply #5 on: January 24, 2017, 04:24:13 PM »
Logged

Offline 70CB750

  • Labor omnia vincit improbus.
  • Really Old Timer ...
  • *******
  • Posts: 14,802
  • Northern Virginia
Re: Swing arm bushings
« Reply #6 on: January 24, 2017, 05:10:54 PM »
Quote from: 77379 on January 24, 2017, 03:56:08 PM
Timbo750, do you know how to contact the guy in Europe or the name of his company that sells the swing arm bushings?

Ebay seller kenosha_kid. I just bought cam chain from him.
Logged
Prokop
_______________
Pure Gas - find ethanol free gas station near you

I love it when parts come together.

Dorothy - my CB750
CB750K3F - The Red
Sidecar


CB900C

2006 KLR650

Offline Jerry Rxman Griffin aka MuthaF'er

  • This MuthaF'er is getting to be a
  • Really Old Timer ...
  • *******
  • Posts: 14,912
  • Bought her new 4/75
Re: Swing arm bushings
« Reply #7 on: January 24, 2017, 05:11:11 PM »
Logged
As of today 3/13/2012 my original owner 75 CB750F has made it through 3 wives, er EX-wives. Free at last.  ;-)

Offline timbo750

  • Expert
  • ****
  • Posts: 759
Re: Swing arm bushings
« Reply #8 on: January 24, 2017, 05:35:45 PM »
Logged

Offline markreimer

  • Expert
  • ****
  • Posts: 1,192
Re: Swing arm bushings
« Reply #9 on: January 24, 2017, 06:13:54 PM »
Yea those are the ones. Bronze, not brass as was mentioned by someone earlier


Sent from my iPhone using Tapatalk
Logged

Offline Stev-o

  • Ain't no
  • Really Old Timer ...
  • *******
  • Posts: 34,324
  • Central Texas
Re: Swing arm bushings
« Reply #10 on: January 24, 2017, 06:28:01 PM »
Logged
'74 "Big Bang" Honda 750K [836].....'76 Honda 550F.....K3 Park Racer!......and a Bomber!............plus plus plus.........

Offline markreimer

  • Expert
  • ****
  • Posts: 1,192
Re: Swing arm bushings
« Reply #11 on: January 24, 2017, 07:13:33 PM »
Careful of the aftermarket carb boots. I had a pair split nearly in half after 2-3 years. I just got a set of Honda replacements in the mail this month actually. These might be one of those pieces that really should be oem


Sent from my iPhone using Tapatalk
Logged

Offline Stev-o

  • Ain't no
  • Really Old Timer ...
  • *******
  • Posts: 34,324
  • Central Texas
Re: Swing arm bushings
« Reply #12 on: January 24, 2017, 08:11:18 PM »
Quote from: markreimer on January 24, 2017, 07:13:33 PM
Careful of the aftermarket carb boots.


Did you buy them from KK? He does not sell China crap.
Logged
'74 "Big Bang" Honda 750K [836].....'76 Honda 550F.....K3 Park Racer!......and a Bomber!............plus plus plus.........

Offline Jerry Rxman Griffin aka MuthaF'er

  • This MuthaF'er is getting to be a
  • Really Old Timer ...
  • *******
  • Posts: 14,912
  • Bought her new 4/75
Re: Swing arm bushings
« Reply #13 on: January 24, 2017, 09:48:01 PM »
These state made in Japan
Logged
As of today 3/13/2012 my original owner 75 CB750F has made it through 3 wives, er EX-wives. Free at last.  ;-)

Offline 77379

  • Full Member
  • *
  • Posts: 64
Re: Swing arm bushings
« Reply #14 on: January 25, 2017, 05:36:48 PM »
Those bushings look like they will work but they are different than what came out of the swing arm which was one piece that ran the width of the swing arm. Are there different types of these bushings? Mine is a '69 and he states his fit 70-78.
Logged

Offline madmtnmotors

  • When did I get to be a
  • Really Old Timer ...
  • *******
  • Posts: 6,106
  • Sunny Central Florida
Re: Swing arm bushings
« Reply #15 on: January 25, 2017, 05:47:30 PM »
Quote from: 77379 on January 25, 2017, 05:36:48 PM
Those bushings look like they will work but they are different than what came out of the swing arm which was one piece that ran the width of the swing arm. Are there different types of these bushings? Mine is a '69 and he states his fit 70-78.

It sounds like you are describing the inner collar. The inner collar extends from side to side, the bushings are only about an inch and a half long.

Can you show us a picture?
Logged
TAMTF...


Wilbur



Projects:
"Evolution": http://forums.sohc4.net/index.php?topic=100352.0
"P.O. Debacle": http://forums.sohc4.net/index.php/topic,126692.msg1441661.html#msg1441661
F2/F3 O-rings: http://forums.sohc4.net/index.php?topic=113672.msg1300721#msg1300721
Cam Tower Studs: https://www.mcmaster.com/#93210a017/=t19sgp
Clean up that nasty harness: http://forums.sohc4.net/index.php?topic=137351.msg1549191#msg1549191
http://forums.sohc4.net/index.php/topic,148188.msg1688494.html#msg1688494
http://forums.sohc4.net/index.php/topic,139544.msg1579364.html#msg1579364
                                          
Charging system diagnosis: http://forums.sohc4.net/index.php?topic=1012.msg8345#msg8345
Get the manuals: http://manuals.sohc4.net/cb750k/
The Dragon: http://forums.sohc4.net/index.php?topic=45183.msg1571675#msg1571675
Headlight Switch: http://forums.sohc4.net/index.php?topic=113986.msg1283236#msg1283236
Branden's leak free top end thread: http://forums.sohc4.net/index.php?topic=107040.0
Engine Lifting Made Easy: http://forums.sohc4.net/index.php/topic,58210.msg1684742.html#msg1684742
                                      http://forums.sohc4.net/index.php/topic,100352.msg1675840.html#msg1675840
Static and Dynamic Timing: http://www.hondachopper.com/garage/carb_info/timing/timing1.html
Airbox Gasket Replacement: http://forums.sohc4.net/index.php/topic,114485.msg1290000.html#msg1290000
"Café" : http://forums.sohc4.net/index.php/topic,84697.msg953814.html#msg953814
PD Carb Choke Linkage: http://forums.sohc4.net/index.php/topic,100352.msg1669248.html#msg1669248
                                    http://forums.sohc4.net/index.php/topic,110931.msg1248354.html#msg1248354
                                    http://forums.sohc4.net/index.php/topic,48858.msg515204.html#msg515204
Follow up on your damn posts: http://forums.sohc4.net/index.php/topic,144305.msg1791605.html#msg1791605
Taiwanese Cam Chain Tensioners:  http://forums.sohc4.net/index.php/topic,155043.msg1774841.html#msg1774841
Gumtwo Seat Cover: http://forums.sohc4.net/index.php/topic,164440.msg1897366.html#msg1897366
Primary Drive: http://forums.sohc4.net/index.php/topic,166063.msg1919278.html#msg1919278
Tank Latch: http://forums.sohc4.net/index.php/topic,165975.msg1919495.html#msg1919495
Shorten your forks: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-shorten-forks-td4042465.html DO NOT CUT THE SPRINGS!
Clutch How To: http://vintage-and-classic-honda-s.456789.n3.nabble.com/How-to-change-and-adjust-a-clutch-SOHC-td4040391.html
Late model K7/K8/F2/F3 front sprocket cover removal: http://forums.sohc4.net/index.php/topic,178428.msg2072279.html#msg2072279
630 to 530 conversion: http://forums.sohc4.net/index.php/topic,180710.msg2094423.html#msg2094423

Sent from my Tandy TRS-80!

Offline 77379

  • Full Member
  • *
  • Posts: 64
Re: Swing arm bushings
« Reply #16 on: January 25, 2017, 05:59:25 PM »
Yes I was going to post the picture but the part is somewhere else. I'll have to round it up when I get back over there in a few days.
Logged
Pages: [1]   Go Up
« previous next »